Submersible Winding Wire

Submersible Winding Wires manufactured by us have an outstanding Electrical, Mechanical, Thermal and Chemical properties. Our Submersible Winding Wires not only fulfill the requirements of all available standards but even better in many respects. Submersible Winding Wires manufactured by us are tear resistant because of their bi-axial orientation. The multiple layer construction of these wires insures high dielectric quality of insulation. The insulation also adds significantly to the tensile strengths of the wire which supports the wire at every point whenever excessive stretching occurs. These winding wires have passed test standards of IS: 8783 -2000 Part IV Sec -3.

Polywin Submersible Winding Wires are far more superior than conventional type of winding wire. It is self explanatory by the following comparative chart.

Name of test
Value specified in standards for PVC insulated winding wire
Values obtained on Polywin (Polymer Insulated) winding wire
Remarks
Thickness of Insulation 0.35 mm 0.20 mm Approx. 40% minitiarised
Heat shock test The insulation shall not show any crack Satisfactory Ok
High Voltage test To withstand 3KV(rms) for one minute Withstood Ok
Shrinkage test The shrinkage shall not exceed 4% 3.5% Ok
Insulation resistance (VoltageResistivity) Ohm-cm
    1. At 27°C 1.28 x 1013 6.18 x 1016 Far Superior
    2. At 70°C 1.28 x 1013 55.03 x 1014 Far Superior
    3. At 85°C 1.46 x 109 20.63 x 1014 Far Superior
    4. At 100°C 1.46 x 109 41.27 x 1013 Far Superior

On specific demand, Polywin winding wire can be produced in Multistranded, Flexible construction. Presently our Polywin winding wires are being used by all the reputed manufacturers in India in their submersible pumps ranging from 0.5 H.P. to 250 H.P. satisfactorily.

Size
m.m.
Resistance
ohm/Km
Elongation
(%)
250V
m.m.
Weight
perKm
500V
m.m.
Weight
perKm
1100V
m.m.
Weight
perKm
3000V
m.m.
Weight
perKm
0.40 136.63 30 0.150 1.30 0.200 1.50 0.30 1.90 0.40 2.30
0.50 87.96 31 0.150 2.05 0.200 2.25 0.30 2.65 0.40 3.05
0.60 60.92 32 0.150 2.85 0.200 3.05 0.30 3.45 0.40 3.85
0.70 44.78 33 0.150 3.85 0.200 4.05 0.30 4.45 0.40 4.85
0.80 34.34 33 0.150 5.00 0.200 5.20 0.30 5.60 0.40 6.00
0.90 27.10 35 0.150 6.20 0.225 6.50 0.30 6.80 0.40 7.20
1.00 21.96 36 0.150 7.70 0.225 8.00 0.30 8.30 0.40 8.70
1.10 18.15 37 0.175 9.30 0.225 9.50 0.30 9.80 0.40 10.20
1.20 15.26 38 0.175 10.90 0.225 11.10 0.30 11.40 0.40 11.80
1.30 12.96 38 0.175 12.80 0.225 13.00 0.30 13.30 0.40 13.70
1.40 11.20 38 0.175 14.70 0.225 14.90 0.35 15.20 0.45 15.60
1.50 9.74 40 0.175 16.90 0.250 17.20 0.35 17.60 0.45 18.00
1.60 8.58 40 NA - 0.250 19.60 0.35 20.00 0.45 20.40
1.70 7.60 40 NA - 0.250 22.00 0.35 22.40 0.45 22.80
1.80 6.79 40 NA - 0.250 24.50 0.35 24.90 0.45 25.30
1.90 6.07 40 NA - 0.250 27.00 0.35 27.40 0.45 27.80
2.00 5.49 40 NA - 0.250 30.00 0.35 30.40 0.45 30.80
2.10 4.98 42 NA - 0.250 32.80 0.35 33.20 0.45 33.60
2.20 4.54 42 NA - 0.250 35.80 0.35 36.20 0.45 36.60
2.30 4.15 42 NA - 0.300 39.80 0.40 40.20 0.50 40.60
2.40 3.81 42 NA - 0.300 42.80 0.40 43.20 0.50 43.60
2.50 3.51 42 NA - 0.300 47.10 0.40 47.50 0.50 47.90
2.60 3.25 43 NA - 0.300 - 0.40 - 0.50 -
2.70 3.01 43 NA - 0.300 - 0.40 - 0.50 -
2.80 2.80 43 NA - 0.300 - 0.40 - 0.50 -
2.90 2.61 43 NA - 0.300 - 0.40 - 0.50 -
3.00 2.44 43 NA - 0.300 - 0.40 - 0.50 -
3.10 2.28 43 NA - 0.300 - 0.40 - 0.50 -

Note: 250Volt grade for single phase pump, 500V for three phase pumPs and 1100V & 3000V for high voltage and extra protection. sizes 0.55mm, 0.65mm, 0.75mm, 0.85mm, 0.95mm, 1.05mm, 1.15mm, 1.25mm, 1.35mm and so on are also manufactued and any other size can also be manufactured as per customer's specification.